JetBoots PrimeUpdated 2 days ago
Shop JetBoots Prime
Travel friendly wireless compression boots for leg recovery anywhere
Key Product Features
- Effortless portability, uncompromised performance
- Fully wireless — no external pumps or hoses to connect to
- Personalize your leg recovery
What's included in box?
- JetBoots Prime device (2 connected compression boots)
- Drawstring backpack
- USB-C charging cable (270 cm)
- AC adapter not included
Using Your Device
Putting On Your Device
- It is recommended that you wear shorts or thin pants while using the device. Reach a comfortable position, either sitting upright or lying down with your legs straight and feet in line with your waist.
- Unzip the compression boots completely and place each leg and foot inside each boot. Your legs should be in the center of each boot with your feet as close to the bottom as possible.
- Keep your legs straight and flat to prevent kinks and folds. Only hold the boots’ edges when handling them. Avoid holding the device by the control panel. Zip both boots up.
DO NOT use the device while standing or walking.
Begin Your Treatment
- To power on your device, press and hold the power button on the control panel. The LED indicators on the control panel will light up when the boots are on.
- Press the pressure button to toggle through four pressure intensity options: 25 mmHg, 50 mmHg, 75 mmHg, 100 mmHg. The pressure setting used in your last treatment will become the default setting for your next treatment. You can also add or subtract pressure during your treatment if desired.
- Press the time button to toggle through four time options: 20 minutes, 40 minutes, 60 minutes, or continuous. The time setting used in your last treatment will become the default setting for your next treatment
- Begin your treatment by pressing the start button. Press the pause button at any point during your treatment to pause and deflate the boots. Press the start button again to resume the treatment.
- Press and hold the power button on the control panel to turn off the device. The device will automatically shut off after 10 minutes of inactivity, including completed or paused treatments. Unzip the compression boots fully and store.
- When not in use or during transport, lock the device to prevent turning it on accidentally. Turn off the device to activate the lock function. Quickly press the power button three times to initiate the lock function. Each LED light will flash sequentially to indicate that the device is locked. Quickly press the button three times again to unlock. Each LED light will flash sequentially (in the opposite direction) to indicate that the device is unlocked.
Charging and LED Indicator Guide
- The device is USB-C enabled and comes with a 6.5 feet (2-meter) USB-C charging cable. The device can charge while the device is powered on or off.
- Connect one end of the charging cable to the USB-C charging port on the device. It is located on the side of the control panel. Plug the other side into a 20 W USB-C power adapter for optimal performance. Using a power adapter with less capacity may not allow you to use the device while charging.
- When the device is on, the LED indicators will show the battery status when the device is on or charging. Turn on the device to check the battery status.
- 1 LED: Low battery
- 2 LEDs: Medium battery
- 3 LEDs: High battery
- The battery life of the device is approximately 180 minutes.
If using a charger from a third party, ensure that it is from a certified manufacturer and has not suffered any structural damage.
Care and Cleaning
This product is NOT waterproof. Do not submerge the device in water or clean it under running water. Do not allow the device to come into contact with corrosive solutions, which can damage the device’s appearance and function.
The JetBoots Prime compression boots have non-porous medical grade material that helps prevent bacteria buildup and provides a resistant surface. The internal overlapping chambers provide a smooth surface to clean, meaning no chamber flaps where bacteria and odors can build up.
- Unzip the boots completely and lay them on a flat surface.
- Use a 70% isopropyl alcohol (IPA) cleaning solution to gently clean the inside of the boots. Never use oil-based cleaning products.
- Wipe down the device’s exterior using a soft cloth that is free of debris to reduce surface contaminants.
- Ensure there is no remaining debris after fully cleaning the device.
- Once you have fully cleaned the device, fully pat dry the surface and hang to dry completely before continuing use.
Specifications
| Battery Life |
|
| Weight |
|
| Size |
|
Dimensions |
|
| Material |
|